8255 PPI DATASHEET PDF

A datasheet, A pdf, A data sheet, datasheet, data sheet, pdf, Intel, PROGRAMMABLE PERIPHERAL INTERFACE. INTEL (Programmable Peripheral Interface). In previous lectures we have discussed how to interface I/O devices with the system bys. If an input device. The Intel (or i) programmable peripheral interface (PPI) chip was developed and manufactured The i was also used with the Intel and Intel and their descendants and found .. “Intel 82c55 PPI Datasheet” (PDF ).

Author: Moogubei Gukasa
Country: Bosnia & Herzegovina
Language: English (Spanish)
Genre: Travel
Published (Last): 1 June 2014
Pages: 283
PDF File Size: 15.46 Mb
ePub File Size: 14.33 Mb
ISBN: 601-6-96086-918-8
Downloads: 36646
Price: Free* [*Free Regsitration Required]
Uploader: Tojasar

As an example, consider an input device connected to at port A. Interrupt logic is supported. Since the two halves of port C are independent, they may be used such that one-half is initialized as an input port while the other half is initialized as an output port. In this mode, the may be used to extend the system bus to a slave microprocessor or to transfer data bytes to and from a floppy disk controller.

This datxsheet is selected when D 7 bit of the Control Word Register is 1. Some of the pins of port C function as handshake lines.

This means that data can be input or output on the same eight lines PA0 – PA7.

Intel 8255

When we wish to use port A or port B for handshake strobed input or output operation, we initialise that port in mode 1 port A and datashfet B can be datasheey to operate in different modes, i.

Address lines A 1 and A 0 allow to access a data register for each port or a control register, as listed below:. Only port A can be initialized in this mode. Retrieved 3 June In datahseet mode, the may be used to extend the system bus to a slave microprocessor or to transfer data bytes to and from a floppy disk datasjeet.

For port B in this mode irrespective of whether is acting as an input port or output portPC0, PC1 and PC2 pins function as handshake lines. Each line of port C Ppii 7 – PC 0 can be set or reset by writing a suitable value to the control word register. For port B in this mode irrespective of whether is acting as an input port or output portPC0, PC1 and PC2 pins function as handshake lines.

  AL WATAN NEWSPAPER OMAN PDF

The two halves of port C can be either used together as an additional 8-bit port, or they can be used as individual 4-bit ports. The Intel or i Programmable Peripheral Interface PPI chip was developed and manufactured by Intel in the first half of the s for the Intel microprocessor.

As an example, consider an input device connected to at port A. Interrupt logic is supported. Retrieved from ” https: Port A can be used for bidirectional handshake data transfer.

Programmable Peripheral Interface – Intel Chipset Datasheet

The ‘s outputs are latched to hold the last data written to them. This mode is selected when D 7 bit of the Control Word Register is 1. The Intel or i programmable peripheral interface PPI chip was developed and manufactured by Intel in the first half of the s for the Intel microprocessor and is a member of the MCS Family of chips.

The functionality of the is now mostly embedded in larger VLSI processing datsaheet as pppi sub-function. If from the previous operation, port A is initialized as an output port and if is not reset before using the current configuration, then there is a possibility of damage of either the input device connected or or both, since both and the device connected will be sending out data. When we wish to use port A or port B for handshake strobed input or output operation, we initialise that port in mode 1 port A and port B can be initilalised to operate in different modes, i.

All of these chips were originally available in a pin DIL package. Input and Output data are latched. For example, if port B and upper port C have to be initialized as input ports and lower port C and port A as output ports all in mode Address lines A 1 and A 0 allow to access a data register for each port or a control register, as listed below:. As an example, if it is needed that PC 5 be set, then in the control word.

  INGENIERIA DE TRANSITO Y CARRETERAS NICHOLAS GARBER DESCARGAR PDF

This means that data can be input or output on the same eight lines PA0 – PA7. It is an active-low signal, i. If an input changes while the port is being read then the result may be indeterminate. It is an active-low signal, i.

Intel – Wikipedia

datasheey The is also directly compatible with the Zas well as many Intel processors. Microprocessor And Its Applications. From Wikipedia, the free encyclopedia. Intel Intel D Microprocessor And Its Applications.

Only port A can be initialized in this mode. If from the previous operation, port A is initialized as an output port and if is not reset before using the current configuration, then there is a possibility of damage of either the input device connected or or both, since both and the device connected will be datashete out data.

By using this site, you agree to the Terms of Use and Privacy Policy. The datawheet are not latched because the CPU only has to read their current values, then store the data in a CPU register datasueet memory if it needs to be referenced at a later time. Acknowledgement and handshaking signals are provided to maintain proper data flow and datashet between the data transmitter and receiver.

This page was last edited on 23 Septemberat The i was also used with the Intel and Intel [1] and their descendants and found wide applicability in digital processing systems. Port A can be used for bidirectional handshake data transfer. Acknowledgement and handshaking signals are provided to maintain proper data flow and synchronisation between the data transmitter and receiver.

The control signal chip select CS pin 6 is used to enable the chip. The two modes are selected on the basis of the value present at the D 7 bit of the control word register.