ADXL datasheet, ADXL circuit, ADXL data sheet: AD – Low Cost +-2 g/+ g Dual Axis iMEMS Accelerometers with Digital Output,alldatasheet. ADXL 2g Dual Axis Accelerometer With Duty Cycle Outputs FEATURES 2- Axis Acceleration Sensor on a Single IC Chip Measures Static Acceleration as. ADXL Accelerometers are available at Mouser Electronics. Mouser offers inventory, pricing, & datasheets for ADXL Accelerometers.

Author: Kazrabei Goltihn
Country: Qatar
Language: English (Spanish)
Genre: Spiritual
Published (Last): 20 April 2013
Pages: 474
PDF File Size: 13.80 Mb
ePub File Size: 5.81 Mb
ISBN: 975-9-60488-919-8
Downloads: 84248
Price: Free* [*Free Regsitration Required]
Uploader: Samusho

When the accelerometer is perpendicular to gravity, its output will change nearly An op amp follower may be required to buffer this pin. The actual resolution of the acceleration signal is, however, limited by the time resolution of the counting devices used to decode the duty cycle.

The resulting movement of the beam allows the user to test if the accelerometer is functional.

The easiest way to null this offset is with a calibration factor saved on the microcontroller or by a user calibration for zero g. Application notes outlining algorithms for calculating acceleration from vatasheet cycle and automated calibration routines are available from the factory. Some key points are presented here. Run the accelerometer at a Lower Voltage, Down to 3 V.

However, in some cases, especially where digital devices such as microcontrollers share the same power supply, digital noise on the supply may cause interference on the ADXLE output.

ADXL202 Data Sheet

Filtering can be used to lower the noise floor and improve the resolution of the accelerometer. Power Cycle the accelerometer. Polysilicon springs suspend the structure over the surface of the wafer and provide a resistance against acceleration forces.

It contains a polysilicon surfacemicromachined sensor and signal conditioning circuitry to implement an open loop acceleration measurement architecture. The equation for the period is: A proper design will take into account the application requirements for bandwidth, signal resolution and acquisition time, as discussed in the following sections.


Its higher sensitivity The following table dayasheet some of the trade-offs. A capacitor still must be added at this point for filtering. Phase sensitive demodulation techniques are then used to rectify the signal and determine the direction of the acceleration. Consult the appropriate Application Note. At this point a pin is available on each channel to allow the user to set the signal bandwidth of the device by adding a capacitor.

At this orientation its sensitivity to changes in tilt is highest. Running the part at 3 V will reduce the supply current from 0.

Therefore, proper ESD precautions are recommended to daatasheet performance degradation or loss of functionality. When one sensor is reading a maximum change in output per degree, the other is at its minimum.

Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Power Cycling When Using the Digital Output An alternative is to run the microcontroller at a higher clock rate and put it into shutdown between readings, allowing the use of the digital output.

Typical Y-Axis Zero g vs. The equation for the 3 dB bandwidth is: This section will outline a general design procedure and discuss the various trade-offs that need to be considered.

The microcontroller should have provisions for software calibration. This will result in greater sdxl202 error generated at the DCM. The outputs are analog voltage or digital signals whose duty cycles ratio of pulsewidth to period are proportional to acceleration.

The device is designed to operate at duty cycle periods between 0. This filtering improves measurement resolution and helps prevent aliasing.


An accelerometer uses the force of gravity as an dxtasheet vector to determine orientation of an object in space. An acceleration will deflect the beam datashert unbalance the differential capacitor, resulting in datasyeet output square wave whose amplitude is proportional to acceleration.

Table III is useful for estimating the probabilities of exceeding various peak values, given the rms value.

The analog bandwidth may be further decreased to reduce noise and improve resolution. Output for 16 Parts REV. An accelerometer is most sensitive to tilt when its sensitive axis is perpendicular to the force of gravity, i. This pin may be left open circuit or connected to common in normal use. Care should be exercised in handling to avoid damage.

BoxNorwood, MAU.

ADXL Data Sheet

One Technology Way, P. ST The ST pin controls the self-test feature. In either of the above approaches, the ADXLE can be turned on and off directly using a digital port pin on the microcontroller to power the accelerometer without additional components.

Often the peak value of the noise is desired. Although the ADXLE features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high-energy electrostatic discharges.

The sensitivity can be determined by the two measurements.

Decoding algorithms for various microcontrollers have been developed. Using the two readings, the sensitivity is: A buffer amplifier is recommended, and may be required in any case to amplify the analog output to give enough resolution with an 8-bit to bit converter.