ISL datasheet, ISL circuit, ISL data sheet: INTERSIL – High- Efficiency, Quad-Output, Main Power Supply Controllers for Notebook Computers . ISL Datasheet, ISL PDF, ISL Data sheet, ISL manual, ISL pdf, ISL, datenblatt, Electronics ISL, alldatasheet, free, datasheet. Renesas Electronics ISL are available at Mouser Electronics. Mouser offers inventory, pricing, & datasheets for Renesas Electronics ISL
|Published (Last):||10 December 2010|
|PDF File Size:||16.79 Mb|
|ePub File Size:||1.57 Mb|
|Price:||Free* [*Free Regsitration Required]|
If possible, make all these connections on the top layer with wide, copper-filled areas. Once activated, the controller continuously monitors the output for undervoltage and overvoltage fault conditions. VIN is also used to power the linear regulators.
Choose R2 to be approximately 10k and solve for R1 using Equation 6. LIR is the ratio of the peak-peak ripple current to the average inductor current. An ultrasonic pulse occurs when the controller datwsheet that no switching has occurred within the last 20? UVP only applies to the buck outputs. The voltage at ILIM pin is the product of 5?
The peak load current ILOAD MAX determines the instantaneous component stress and filtering requirements and thus drives output capacitor selection, inductor saturation rating and the design of the current-limit circuit.
EN1 or EN2 falling below 1. The internal digital soft-start timer begins to ramp up the maximum-allowed current limit during start-up. Dimensions in for Reference Only. On the board’s top side power planesmake a star ground to minimize crosstalk between the two sides.
Leave open if there is no load. A of quiescent current while in shutdown.
isl datasheet & applicatoin notes – Datasheet Archive
Therefore, the exact current-limit characteristic and maximum load capability are a function of the current-limit threshold, inductor value and input and output voltage. In non-CPU applications, the output capacitor’s size depends on how much ESR is needed to maintain an acceptable level of output voltage ripple: This interleaves the current pulses drawn by the two switches and reduces the overlap time where they add together. When combined with the undervoltage-protection circuit, this current-limit method is effective in almost every circumstance.
Ensure that the conduction losses at the minimum input voltage do not exceed the package thermal limits or violate the overall thermal budget. The high-side switch ON-time is inversely proportional to the battery voltage as measured by the VIN input and proportional to the output voltage.
Temperature limits established by characterization and are not production tested. This ultrasonic pulse-skipping mode eliminates audio-frequency modulation that would otherwise be present when a lightly loaded controller automatically skips pulses.
Keep the resistance low between the star ground and the source of the synchronous rectifiers for accurate current limit. As h approaches 1, the absolute minimum dropout point, the inductor current is less able to increase during each eatasheet cycle and VSAG greatly increases unless additional output capacitance is used.
All Rights Reserved All other trademarks mentioned are the property of their respective owners. There is an internal 5?
(PDF) ISL6236 Datasheet download
RF interference in sensitive applications. For a given value of h, the minimum operating voltage can be calculated as: Ignoring the sag due to finite capacitance: Connect the output power planes VCORE and system ground planes directly to the output filter capacitor positive and negative terminals with multiple vias.
A V mV 93 3 FN F capacitor if loaded. Connect to the SMPS1 output. The output of Catasheet can also be adjusted from 0. The output capacitance must also be high enough to absorb the inductor energy while transitioning from full-load to no-load conditions without tripping the overvoltage fault latch.
All Rights Reserved All other trademarks mentioned are the property of their respective owners. For more information on. However, in some cases it may be desirable to deliberately introduce some trace length between the OUT connector node and the output filter capacitor.
Forced-PWM mode is most useful for reducing audio-frequency noise, improving load-transient isl623, providing sink-current capability for dynamic output voltage adjustment, and improving the cross-regulation of multiple-output applications that use a flyback transformer or coupled inductor.
UVP is ignored for at least 20ms typicalafter start-up or after a rising edge on EN.
POK is actively held low in shutdown, standby, and soft-start. Supply Controllers for Notebook. CP output voltage is: MSL please see techbrief TB Drive EN2 below 0. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use.
The ISL is designed primarily for battery-powered applications where high efficiency and low-quiescent supply current are critical. F Q3b C4 0. Intersil Pb-free products are MSL classified. Another one-shot sets a minimum OFF-time ns typ.